Skip to main content
emobility.academy
Engineers at simulation workstations in the DIYguru EV lab

For OEMs, Tier-1 suppliers & EV start-ups

E-Mobility Project Outsourcing: EV Engineering from Design to Testing

Hand a defined EV engineering package to a team that works on EV systems every day. DIYguru takes on design and simulation (vehicle and powertrain sizing, battery pack and BMS design, MATLAB / Simulink models, ANSYS and SolidWorks work), builds and bench-tests prototypes, and prepares the documentation you need before testing to AIS standards at ARAI or ICAT.

  • Battery pack, BMS and powertrain design
  • MATLAB / Simulink, ANSYS and SolidWorks work
  • Prototype builds and bench tests in our labs
  • AIS test-preparation documentation

Outsource an EV engineering project

Tell us about the work. We reply within one working day to set up a scoping call.

Scope

Design · simulation · prototype · test prep

Engagement

Fixed scope or milestones

For

OEMs, Tier-1s, EV start-ups

Delivery

Remote + Delhi / Pune labs

Why it matters

Why outsource EV engineering to DIYguru

EV programmes need specialist work in short bursts: a battery pack sized and packaged, a BMS architecture reviewed, a powertrain model built, a test plan written before a homologation slot. Hiring a full team for each of those is slow, and general engineering service providers often lack EV depth.

DIYguru's engineers build the hardware our own labs run on. We developed EV training workbenches with Tadpole Projects (incubated at IIT Delhi), an EV charging kit with EVI Technologies under the mentorship of Dr. B.K. Panigrahi of IIT Delhi, hardware test rigs developed with IIT Delhi and an ARM Cortex-based embedded kit, and we train engineering teams at Hyundai Motor India, HL Mando, Honda Car India and Sonalika Tractors on the same systems.

EV depth

Batteries, BMS, motors, power electronics, charging and embedded control are what we work on every day.

Design to bench

Simulation results checked on real hardware in our Delhi and Pune labs.

Clear deliverables

Every package is scoped with deliverables, review points and acceptance criteria.

NDA and IP terms

We work under NDA, with ownership of design files and data set out in the contract.

Formats

Engagement models

Start with one package or combine them. Every project is quoted after a scoping call.

Per package Remote · delivered online

EV design & simulation

Vehicle and powertrain sizing, range and performance models in MATLAB / Simulink, battery pack and BMS design, structural and thermal analysis in ANSYS, and CAD in SolidWorks.

Quoted for your project

Scope a design package
Per package Delhi / Pune lab

Prototype build & bench testing

Battery pack assembly, BMS and controller integration, wiring harnesses, and bench tests of motors, packs and chargers on our test rigs, with test reports.

Quoted for your project

Scope a prototype
Per package Remote + on site

Testing & homologation support

Test plans, technical documentation and pre-test checks against the applicable AIS standards (such as AIS-156 and AIS-038 Rev 2 for traction batteries) before you test at ARAI, ICAT or another accredited agency.

Quoted for your project

Scope test preparation
Custom On site or online

Training for your engineering team

Pair a project with training: we train your engineers on the systems we work on, as we have for teams at Hyundai Motor India, HL Mando and Honda Car India.

Quoted for your project

See corporate training

Scope

What we can take on

01

Vehicle & powertrain

  • Vehicle requirements and duty-cycle analysis
  • Motor, controller and gear-ratio sizing
  • Range, gradeability and acceleration models
  • MATLAB / Simulink and QSS vehicle models

02

Battery pack & BMS

  • Cell selection and series-parallel configuration
  • Pack mechanical and thermal design
  • BMS architecture, protection and balancing
  • SOC / SOH estimation models

03

CAD & CAE

  • SolidWorks 3D models and drawings
  • ANSYS structural and thermal analysis
  • Battery enclosure and mounting design
  • Design reviews

04

Embedded & electronics

  • Microcontroller firmware for EV subsystems
  • CAN communication and diagnostics
  • Sensor integration and data logging
  • Charger and EVSE integration

05

Prototype & test

  • Pack and harness builds
  • Motor, controller and pack bench tests
  • Charging tests on EVSE
  • Test reports with recorded data

06

Homologation support

  • Mapping applicable AIS / CMVR requirements
  • Test plans and pre-test checks
  • Technical documentation for the test agency
  • Support during ARAI / ICAT testing

Outcomes

What you receive

  • A written scope with deliverables, timeline and acceptance criteria
  • Design files, models and calculations in agreed formats
  • Simulation and test reports with recorded data
  • Prototype hardware where the package includes a build
  • Documentation ready for your test agency
  • A handover session for your engineering team

Who it is for

Who we work with

EV start-ups

Needing design, simulation or test preparation before building a full in-house team.

OEMs

With overflow work, a new platform study or a specialist package on batteries or powertrain.

Tier-1 suppliers

Developing packs, BMS, motors, controllers or chargers for EV programmes.

Retrofit & fleet companies

Converting or adapting vehicles and needing calculations and documentation.

How it works

Four simple steps

  1. 1

    Share the problem

    The vehicle or subsystem, stage, timeline and any data you can share under NDA.

  2. 2

    Scoping call & proposal

    We agree deliverables, milestones, acceptance criteria and a quotation.

  3. 3

    Engineering work

    Design, simulation, build or test work, with a review at each milestone.

  4. 4

    Handover

    Files, reports and a walkthrough for your team, with support until acceptance.

FAQs

Frequently asked questions

What kind of EV engineering work do you take on?

Defined packages in vehicle and powertrain sizing, battery pack and BMS design, MATLAB / Simulink modelling, ANSYS and SolidWorks work, embedded firmware, prototype builds, bench testing and test-preparation documentation.

Are you a homologation or testing agency?

No. Type-approval testing in India is done by accredited agencies such as ARAI and ICAT. We help you prepare: mapping the applicable AIS standards, writing test plans, running pre-test checks and preparing the technical documentation.

Do you sign an NDA?

Yes. We sign an NDA before you share drawings, data or specifications, and the contract sets out who owns the design files and results.

Can you build prototypes?

Yes, for subsystems such as battery packs, harnesses and test set-ups, built and bench-tested at our Delhi and Pune labs. Larger builds are scoped case by case.

How is a project priced?

Each package is quoted after a scoping call, either as a fixed price for a defined scope or against agreed milestones.

Do you work with companies outside India?

Yes, for design, simulation and documentation work that can be delivered remotely. Hands-on work runs in our Indian labs.

Can you also train our engineers?

Yes. DIYguru runs EV training for engineering teams, including at Hyundai Motor India, HL Mando, Honda Car India and TCS, and can train your team on the systems we design for you.

Get EV engineering work done by specialists

Tell us about the work. We reply within one working day to set up a scoping call.

Request a proposal